Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
They are making several great observations on the subject of A Step-by-Step Guide to Installing a Bathtub in general in the content underneath.
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately hard task. If the old bathtub is easily easily accessible, the job can move rapidly; if you have to open a wall surface to remove the old tub as well as position the brand-new bath tub, the task is a lot harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as embeded in the new one. Make certain you have actually qualified yourself for the job as well as fit attempting it. Rather than hiring a professional to take over a halfway-completed job, it is much better to take into consideration using one before you start. Opportunities are you might need an expert plumber to make tube connections.
This write-up will assist you install a brand-new bathtub in your shower room if you have already acquired a new tub as well as do not require to transform the arrangement of your previous water supply pipes.
Your devices and also product list should comprise the following:
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the called for placement. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Turn on the water supply and also examine all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill up the bathtub as well as additionally examine the overflow outlet and also the typical electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and also sealing around the bathtub must wait till the tub has been utilized a minimum of when as this will settle it into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making certain that the washers are in area in between the faucet and also the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap connectors. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, leading to issues with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to enable the activity experienced when the tub is in use. The sealant can fracture rather early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was introduced to that article about How to Install a Bathtub Yourself through an acquaintance on a different domain. So long as you liked our post please be sure to pass it around. Thanks a bunch for your time. Come back soon.
Quality care? Call. Report this page